Gas Detector Tube

• Model number: CGB
• Size (mm): 400 x 400 x 400 *Excluding knob.
• Usage: Gas replacement
• Body material: PMMA (acrylic)
• Window portion size: 280 x 280mm
• Gas replacement cock: Outer diameter f6mm cock for tube x 2 pieces included
• Weight: 6kg
• Accessories: Gloves for Glove box x 1 pair
• It is small glove box of transparent acrylic and useful for introspection.
• Because it has gas replacement port, gas can be easily replaced.
• It is with handle for easy portability.

•
• Target gas: 1 Type of Ar, N2O, CO2, He Air C2H2
• Primary pressure: 10 kg / cm2 (About 0.98 MPa) MAX
• flow rate: 30 L / minMAX
• Secondary pressure: 0 to 5 kg / cm2 (0 to about 0.49 MPa) (* () is a Pa conversion value.)
• Connection tube outer diameter: f6 mm
• flow rate: 10 L / minMAX
• Pressure breakdown: about 0.69 MPa (7 kg / cm2)
• Heat resistant: 60 ? CMAX
• Connection tube outer diameter: f6 mm
• Housing: PMMA (acrylic)
• Model number: FMC-1
• Size (mm): 230 x 133 x 190
• Adjusts the pressure and flux of introductory gas and introduces gas at the time of gas replacement and can be introduced the gas certainly.
• It is simultaneously controllable 3 sets at a maximum.

• Model number: Gas replacement unit
• Flowmeter: 10L/min
• Regulator Set pressure range: 0.1 - 0.8MPa
• Bracket fitting x 2 pieces (for outer diameter f6mm tube) included

• Material: External/steel plate melamine bake coating, Internal/stainless steel (SUS430),
• Shelf board mounting pitch: 25mm
• Shelf board load capacity: Approximately 15kg/stage
• Total withstand load: Approx 30kg
• Weight: 30kg
• *With key
• Gas replacement cock: One touch quick joint (outer diameter f 6mm, Inner diameter f4mm for tube)
• Number of stages: 13 stages
• PE (polyethylene) made adjuster x 4 pieces
• Front glass window: Using 5mm
• Nitrogen gas (N2) gas cock standard equipment for replacement
• Outer dimensions: 515 x 418 x 555mm
• Inner dimension: 375 x 375 x 400mm
• Accessories: Drawer x 8 pieces, Middle partition plate x 8 sheets, Silica gel plate x 2 plates
• Model number: Type 1

• Model number: DG-1N
• Outer dimension (mm): 450 x 450 x 900
• Inner dimension (mm): 406 x 400 x 740
• Material: Steel plate melamine baking coating
• Shelf board load capacity: Approximately 30kg/board
• Weight: 30kg
• Gas introduction, discharge port: Introduction/outer diameter f6mm tube for quick fittings, Discharge/outer diameter f12mm tube for quick joint
• Accessories: Shelf board x 3, Low humidity digital thermo-hygrometer (THI-HP) x 1 piece
• DG-3N?4N:Top and bottom is separated. Possible to replace with gas into only upper or upper and lower cabinet(only lower cabinet is not available).
• DG-2N?4N is full open type which does not have vertical divider in center of door, so wide storage object can be taken in and out easily.
• To DG-1N?2N, optional casters can be attached.

• Model number: DG-2N
• Outer dimension (mm): 900 x 450 x 900
• Inner dimension (mm): 856 x 400 x 740
• Material: Steel plate melamine baking coating
• Shelf board load capacity: Approximately 30kg/board
• Weight: 50kg
• Gas introduction, discharge port: Introduction/outer diameter f6mm tube for quick fittings, Discharge/outer diameter f12mm tube for quick joint
• Accessories: Shelf board x 3, Low humidity digital thermo-hygrometer (THI-HP) x 1 piece
• DG-3N?4N:Top and bottom is separated. Possible to replace with gas into only upper or upper and lower cabinet(only lower cabinet is not available).
• DG-2N?4N is full open type which does not have vertical divider in center of door, so wide storage object can be taken in and out easily.
• To DG-1N?2N, optional casters can be attached.

• Model number: DG-3N
• Outer dimension (mm): 600 x 650 x 1800
• Inner dimension (mm): 536 x 600 x 675 x 2 rooms
• Material: Steel plate melamine baking coating
• Shelf board load capacity: Approximately 30kg/board
• Weight: 104kg
• Gas introduction, discharge port: Introduction/outer diameter f6mm tube for quick fittings, Discharge/outer diameter f12mm tube for quick joint
• Accessories: Shelf board x 4, Low humidity digital thermo-hygrometer (THI-HP) x 2 pieces
• DG-3N?4N:Top and bottom is separated. Possible to replace with gas into only upper or upper and lower cabinet(only lower cabinet is not available).
• DG-2N?4N is full open type which does not have vertical divider in center of door, so wide storage object can be taken in and out easily.
• To DG-1N?2N, optional casters can be attached.

• Model number: DG-4N
• Outer dimension (mm): 1200 x 650 x 1800
• Inner dimension (mm): 1136 x 600 x 675 x 2 rooms
• Material: Steel plate melamine baking coating
• Shelf board load capacity: Approximately 30kg/board
• Weight: 150kg
• Gas introduction, discharge port: Introduction/outer diameter f6mm tube for quick fittings, Discharge/outer diameter f12mm tube for quick joint
• Accessories: Shelf board x 4, Low humidity digital thermo-hygrometer (THI-HP) x 2 pieces
• DG-3N?4N:Top and bottom is separated. Possible to replace with gas into only upper or upper and lower cabinet(only lower cabinet is not available).
• DG-2N?4N is full open type which does not have vertical divider in center of door, so wide storage object can be taken in and out easily.
• To DG-1N?2N, optional casters can be attached.

• Model number: ATM-02
• Size (mm): 190 x 170 x 122
• Hot plate: Aluminum block (teflon coating)
• Heater: Cartridge heater (120V x 60W x 1 piece)
• Measurement temperature range: Room temperature - 300?
• Temperature display: Digital display (unit is 1?)
• Temperature sensor: Pt resistance temperature detector
• Temperature adjustment: Thyristor Voltage control method
• Visual loupe: Steinheil loupe, at 5-fold magnification
• Casing: Steel plate baking coating
• Cover: PMMA (acrylic)
• Power supply: 100VAC 50/60Hz
• Body weight: 2.2kg
• Power cord: 1.5m (3P plug)
• *Cover glass is not attached.
• Melting point and softening point of compound and resin and wax etc. can measure simply.
• The overheating prevention function is equipped.
• Since Teflon*R* coating of heat board is carried out, hard to become dirty.
• ATM-02 has flat heat board and suitable for measurement by clipping with coverglass.

• Model number: MAS-1
• Vacuum attainment level: -75kPa
• Highest exhaust Pressure forces: 0.2MPa
• Intake gas flow rate 12L/min
• Exhaust gas flow rate 12L/min
• Connection port size: f7.5mm (Made of metal)
• Power supply: AC100V 50/60Hz 0.8A
• Gas contact unit material: Silicone, PA (Nylon), PTFE (4 Ethylene fluoride), brass Ni Plating
• For both discharge and suction
• Size: 195 x 112 x 195mm
• It is convenient for carrying around and compact design and with handles.
• It is dry air pump that is oil-free.
• Pressure and suction in one is possible.

• Model number: Quartz furnace core tube
• Outer diameter: f30 x f24 x 500mm
• If reactor core pipe and a gas substitution kit are used, heating under inactive environment is possible.
• Core pipe can be chosen by materials.
• It is provided the automatic overheating temperature prevention function interlocked with preset temperature, and the full independence type overheating prevention function, also the burnout function which detects the abnormalities in sensor is also equipped.
• When door is opened, the safety feature which cuts turning on electricity to heater sticks.
• Gas substituned unit gets better for sealing property bu O-ring(not perfectly sealed).

• Model number: Quartz furnace core tube
• Outer diameter: f50 x f44 x 500mm
• If reactor core pipe and a gas substitution kit are used, heating under inactive environment is possible.
• Core pipe can be chosen by materials.
• It is provided the automatic overheating temperature prevention function interlocked with preset temperature, and the full independence type overheating prevention function, also the burnout function which detects the abnormalities in sensor is also equipped.
• When door is opened, the safety feature which cuts turning on electricity to heater sticks.
• Gas substituned unit gets better for sealing property bu O-ring(not perfectly sealed).

• Model number: Quartz furnace core tube
• Outer diameter: f70.5 x f64.5 x 500mm
• If reactor core pipe and a gas substitution kit are used, heating under inactive environment is possible.
• Core pipe can be chosen by materials.
• It is provided the automatic overheating temperature prevention function interlocked with preset temperature, and the full independence type overheating prevention function, also the burnout function which detects the abnormalities in sensor is also equipped.
• When door is opened, the safety feature which cuts turning on electricity to heater sticks.
• Gas substituned unit gets better for sealing property bu O-ring(not perfectly sealed).

• Model number: Gas replacement unit for TMF-300N
• Adaptive furnace core tube: Ceramic, Alumina 99%, Quartz
• Accessories: Aluminum cover x 2, BS valve (for pipe inner diameter f6mm) x 1, Exhaust plug screw x 1, O-ring x 2
• If reactor core pipe and a gas substitution kit are used, heating under inactive environment is possible.
• Core pipe can be chosen by materials.
• It is provided the automatic overheating temperature prevention function interlocked with preset temperature, and the full independence type overheating prevention function, also the burnout function which detects the abnormalities in sensor is also equipped.
• When door is opened, the safety feature which cuts turning on electricity to heater sticks.
• Gas substituned unit gets better for sealing property bu O-ring(not perfectly sealed).

• Model number: Gas replacement unit for TMF-500N
• Adaptive furnace core tube: Ceramic, Alumina 99%
• Accessories: Aluminum cover x 2, BS valve (for pipe inner diameter f6mm) x 1, Exhaust plug screw x 1, O-ring x 2
• *Quartz furnace core tube cannot be used. Use the gas replacement unit for quartz furnace core tube.

• Model number: Unit for quartz furnace core tube for TMF-500N
• Adaptive furnace core tube: Quartz

• Model number: GTB-60
• Material: Cover/PC (polycarbonate), Wire fastener/PA (nylon 66)
• Recommended gas flow: To 3L/min (MAX)
• Valve: IN/PISCO BVLC20-0602, OUT/BVVC20-0802 (OUT)
• Positive pressure safety valve: Minimum operating pressure 98.1Pa (10mmAq)
• Size: 450 x 400 x 345mm
• *You cannot use it in an atmosphere of 80? or more. *Make sure you place decompression equipment in front of gas inlet, Do not apply gas pressure of more than 294Pa (30mmAg). *You cannot use it in decompression environment.
• Such as nitrogen atmosphere etc. can be made the environment of hot plate in simple.

• Model number: GTB-105
• Material: Cover/PC (polycarbonate), Wire fastener/PA (nylon 66)
• Recommended gas flow: To 3L/min (MAX)
• Valve: IN/PISCO BVLC20-0602, OUT/BVVC20-0802 (OUT)
• Positive pressure safety valve: Minimum operating pressure 98.1Pa (10mmAq)
• Size: 600 x 500 x 395mm
• *You cannot use it in an atmosphere of 80? or more. *Make sure you place decompression equipment in front of gas inlet, Do not apply gas pressure of more than 294Pa (30mmAg). *You cannot use it in decompression environment.
• Such as nitrogen atmosphere etc. can be made the environment of hot plate in simple.

• Model number: Activated carbon filter (for acid gas)
• Size (mm): 150 x 150 x 20
• Weight (kg): 0.12
• It is exhaust hood of space-saving type which makes smell and gas adsorb with activated carbon.

• Model number: Metal fitting for fixing decompression valve (1 piece)
• Provided with palm-sized small container to fill high-pressure gas.
• Suitable for small amount of gas displacement test and use in place where piping does not reach out or high-pressure gas tank can not carried in.