Heating Devices

• Specifications: Without measurement hole
• Drain water: Natural evaporation method
• Temperature settings range : 3 - 45 deg C
• Convection system : Natural convection system (5 sides cooling and heating)
• Cooling heater: Peltier Element
• Setting temperature: 1 deg C unit
• Temperature distribution accuracy: +/- 0.5 deg C (at 37 deg C)
• Temperature control accuracy: +/- 0.5 deg C
• Material : Frame/Steel painted finish , Interior/Aluminium , Door surface/ABS Plastic
• Power supply: AC100 to 240 V 50/60 Hz
• Power cord length : 2 meters (2P plug)
• Safety devices: overcurrent protection fuses
• Capacity: 28L
• Outer dimensions : 413 x 420 x 485mm
• Innder dimensions: 219 x 329 x 369mm
• Weight: 13.5 kg
• Accessories: Shelf board x 2 pieces
• Power consumption: 75W
• Country of origin: JAPAN
• Control Panel : English
• Plug: Type A (https://en.wikipedia.org/wiki/Mains_electricity_by_country)

• Reached vacuum: 58.6 kPa
• Seal system: Lower heating
• Seal ability: 0.4 mm or less / 2 pieces
• power supply: AC100V 50 / 60Hz 1050 (560) W
• * In parentheses, 5 mm width seal heating
• Nagatoshi power cord: 3 m (2P Type)
• Weight: 12 kg
• Model number: V 301
• Seal size (Width ? Long mm): 10 (5) x 300
• main unit size (mm): 400 x 420 x 228

• Reached vacuum: 58.6 kPa
• Seal system: Heating upper and lower
• Seal ability: 0.5 mm or less / 2 pieces
• power supply: AC100V 50 / 60Hz 1050 W
• Nagatoshi power cord: 3 m (2P Type)
• Weight: 12.7 kg
• Model number: V 301-10 W
• Seal size (Width ? Long mm): 10 x 300
• main unit size (mm): 400 x 420 x 228

• System: Vacuum drying by decompressed chamber direct heating
• Operating temp. range: 40~200?
• Operating pressure range: 101~0.1kPa (760~1 Torr)
• Temp. control accuracy: ?1.0?(at 200?) JTM K05
• Temp. fluctuation: 3.0?(at 200?) JIS C60068
• Max. temp. reaching time: Approx. 80 min.
• Internal dimentions(WxDxH): 450 x 450 x 450mm
• External dimentions(WxDxH): 670 x 669 x 1500mm
• Internal capacity: Approx. 91L
• No. of steps/pitch: 4 steps/105mm
• Shelf load capacity : Approx. 15 kg/pc
• Power supply: AC220V 50/60Hz single phase 11A (plug is not included)
• Weight: Approx. 210kg
• Accessories: Stainless shelf x 2, Manual

• System: Vacuum drying by decompressed chamber direct heating
• Operating temp. range: 40~200?
• Operating pressure range: 101~0.1kPa (760~1 Torr)
• Temp. control accuracy: ?1.0?(at 200?) JTM K05
• Temp. fluctuation: 3.0?(at 200?) JIS C60068
• Max. temp. reaching time: Approx. 100 min.
• Internal dimentions(WxDxH): 600 x 600 x 600mm
• External dimentions(WxDxH): 820 x 819 x 1650mm
• Internal capacity: Approx. 216L
• No. of steps/pitch: 4 steps/140mm
• Shelf load capacity : Approx. 15 kg/pc
• Power supply: AC220V 50/60Hz single phase 15A (plug is not included)
• Weight: Approx. 310kg
• Accessories: Stainless shelf x 2, Manual

• Model number: HHP-1
• Size: 150 x 280 x 443mm
• Weight: Approx 9kg
• Up or down hot plate Distance: 38 - 63mm (stroke: 25m)
• Heating temperature: R.T. +20 - 200?
• Temperature settings: Analog
• Sensor: K class thermocouple
• Material: Press Body/cast Iron baking coating, Lever/cast iron (Chromium Plating), Temperature control/steel coating, Base/Phenol Resin, Top board/aluminum
• Heater: 160W x 1
• Power supply: 100VAC 50/60Hz
• Power cord length: 2.5mm
• Suitable for hot pressing of samples in a size as small as a tablet.
• This press can be used with a die(f7~14*mm*?sold separately).
•
• The upper and lower hot plates separately heat samples.

• Model number: H400-01
• Weighted (t): 0 - 1
• Size (mm): 625 x 460 x 500
• Weight (kg): Approx 70
• Hot plate size: 200 x 150mm
• Hot plate stroke: 0 - 90mm
• Heating temperature: R.T. +20 - 400?
• Heater capacity: 1150W/heating plate x 2
• Temperature adjustment: PID type
• Pressure gauge: With left needle, analog display
• Power supply: AC200V 50/60Hz
• Power cord length: 2.5m
• Plug shape: Without plug
• *it cannot hold pressure for long hours.
• *Pressure is recommended for use in 50% or more of the largest value.
• Allows for hot pressing operations at higher temperature(Max. 400?)compared with conventional press, ensuring wide range of applications such as heating compression molding.
• Capable of manufacturing plastic sheets and molding samples.
• This press is compatible with optional hot press dies(1-6002-11~? P.211).
• Driven by hydraulic pressure, it ensures easy weight application.
• Peak hold pressure gauge with 2-pointers allows you to check the applied pressure.

• Model number: H400-05
• Weighted (t): 0 - 5
• Size (mm): 635 x 490 x 535
• Weight (kg): Approx 73
• Hot plate size: 200 x 150mm
• Hot plate stroke: 0 - 90mm
• Heating temperature: R.T. +20 - 400?
• Heater capacity: 1150W/heating plate x 2
• Temperature adjustment: PID type
• Pressure gauge: With left needle, analog display
• Power supply: AC200V 50/60Hz
• Power cord length: 2.5m
• Plug shape: Without plug
• *it cannot hold pressure for long hours.
• *Pressure is recommended for use in 50% or more of the largest value.
• Allows for hot pressing operations at higher temperature(Max. 400?)compared with conventional press, ensuring wide range of applications such as heating compression molding.
• Capable of manufacturing plastic sheets and molding samples.
• This press is compatible with optional hot press dies(1-6002-11~? P.211).
• Driven by hydraulic pressure, it ensures easy weight application.
• Peak hold pressure gauge with 2-pointers allows you to check the applied pressure.

• Model number: H400-15
• Weighted (t): 0 - 15
• Size (mm): 650 x 490 x 620
• Weight (kg): Approx 87
• Hot plate size: 200 x 150mm
• Hot plate stroke: 0 - 90mm
• Heating temperature: R.T. +20 - 400?
• Heater capacity: 1150W/heating plate x 2
• Temperature adjustment: PID type
• Pressure gauge: With left needle, analog display
• Power supply: AC200V 50/60Hz
• Power cord length: 2.5m
• Plug shape: Without plug
• *it cannot hold pressure for long hours.
• *Pressure is recommended for use in 50% or more of the largest value.
• Allows for hot pressing operations at higher temperature(Max. 400?)compared with conventional press, ensuring wide range of applications such as heating compression molding.
• Capable of manufacturing plastic sheets and molding samples.
• This press is compatible with optional hot press dies(1-6002-11~? P.211).
• Driven by hydraulic pressure, it ensures easy weight application.
• Peak hold pressure gauge with 2-pointers allows you to check the applied pressure.

• Model number: HDBS-1
• External dimensions: 260 x 230 x 180mm
• Temperature display precision: +/- 2?
• Temperature sensor: K class thermocouple
• Temperature control: PID control
• Motor: DC brushless motor
• Rotation speed: 0 - 1200rpm
• Block hole: f92mm x depth 100mm x 1 hole
• Material: Exterior/steel baking finish, Block part/aluminum
• Power supply: 100VAC, 50/60Hz
• Power cord length: 2.5m (3P plug, with 2P conversion adapter)
• Weight: 6.5kg
• Accessories: Stir bar (f8 x 30mm) x 1 pc
• Temperature range (?): Room temperature +5 - 150
• 1 strand
• Enables stirring with heating in 500*ml* beaker.
• The separately-sold adapter sleeve allows various vessels to be used.

• Model number: HP2020
• Highest temperature: 300 ?
• Plate size: 200 x 200mm
• Plate material: Aluminum
• Size: 202 x 202 x 64mm
• Heater capacity: 700W
• Temperature sensor: K class thermocouple
• Mounting screw hole: M4 tapping 4 points
• Power supply: 100VAC 50/60Hz
• *Please use it by connecting to temperature controller or Slidac (temperature controller P.360 1-7582-01, etc. Please be careful of power consumption. ). *Power cord is not included.
• These simple hot plates consist with heating plate, heater and thermocouple temperature sensor.

• Model number: HP4030
• Highest temperature: 300 ?
• Plate size: 400 x 300mm
• Plate material: Aluminum
• Size: 402 x 302 x 64mm
• Heater capacity: 1400W
• Temperature sensor: K class thermocouple
• Mounting screw hole: M4 tapping 4 points
• Power supply: 100VAC 50/60Hz
• *Please use it by connecting to temperature controller or Slidac (temperature controller P.360 1-7582-01, etc. Please be careful of power consumption. ). *Power cord is not included.
• These simple hot plates consist with heating plate, heater and thermocouple temperature sensor.

• Model number: MC-1
• Size: 270 x 210 x 260mm (body)
• Temperature adjustment range: -5 - 80?
• Cooling and heating method: Peltier element
• Temperature control system: PID control
• Temperature sensor: K class thermocouple
• Power supply: 100VAC, 50/60Hz
• Material: Body/ABS resin, Transparent cover/PS (polystyrene), Bus part/aluminum (fluorine resin coating), Controller/steel coating
• Body weight: Approx 8kg
• Controller size: 70 x 260 x 190mm
• Power consumption: Maximum approx 100W
• Power cord length: 2m (2P plug)
• *Cooling unit is not included in the package.
• Accurate temperature control is realized by sensing the block temperature and liquid temperature.
• The electronic cooling method adopting Peltier elements assures silent and clean operation.
• Precise temperature control is enabled for both heating and cooling.

• Model number: H300-01
• Weighted (t): 0 - 1
• Size (mm): 470 x 350 (500) x 456
• Weight (kg): Approx 54
• Hot plate size: 200 x 150mm
• Hot plate stroke: 0 - 90mm
• Heating temperature: R.T. +20 - 300?
• Heater capacity: 660W/heating plate x 2 sheets
• Temperature adjustment: PID type
• Pressure gauge: With left needle, analog display
• Power supply: 100VAC 50/60Hz
• Power cord length: 2.5m (with 3P plug)
• Application: To fabricate a compression forming type test and samples of resin and various powder.
• Capable of manufacturing plastic sheets and molding samples.
• Suitable for heating compression molding tests of various materials.
• Driven by hydraulic pressure, it ensures easy weight application.
• Peak hold pressure gauge with 2-pointers allows you to check applied pressure.
• Equipped with load cell for measuring of applied weight, it digitally displays the weighted value(H300-10D).

• Model number: H300-05
• Weighted (t): 0 - 5
• Size (mm): 470 x 380 (735) x 490
• Weight (kg): Approx 55
• Hot plate size: 200 x 150mm
• Hot plate stroke: 0 - 90mm
• Heating temperature: R.T. +20 - 300?
• Heater capacity: 660W/heating plate x 2 sheets
• Temperature adjustment: PID type
• Pressure gauge: With left needle, analog display
• Power supply: 100VAC 50/60Hz
• Power cord length: 2.5m (with 3P plug)
• Application: To fabricate a compression forming type test and samples of resin and various powder.
• Capable of manufacturing plastic sheets and molding samples.
• Suitable for heating compression molding tests of various materials.
• Driven by hydraulic pressure, it ensures easy weight application.
• Peak hold pressure gauge with 2-pointers allows you to check applied pressure.
• Equipped with load cell for measuring of applied weight, it digitally displays the weighted value(H300-10D).

• Model number: H300-15
• Weighted (t): 0 - 15
• Size (mm): 570 x 380 (725) x 570
• Weight (kg): Approx 70
• Hot plate size: 200 x 150mm
• Hot plate stroke: 0 - 90mm
• Heating temperature: R.T. +20 - 300?
• Heater capacity: 660W/heating plate x 2 sheets
• Temperature adjustment: PID type
• Pressure gauge: With left needle, analog display
• Power supply: 100VAC 50/60Hz
• Power cord length: 2.5m (with 3P plug)
• Application: To fabricate a compression forming type test and samples of resin and various powder.
• Capable of manufacturing plastic sheets and molding samples.
• Suitable for heating compression molding tests of various materials.
• Driven by hydraulic pressure, it ensures easy weight application.
• Peak hold pressure gauge with 2-pointers allows you to check applied pressure.
• Equipped with load cell for measuring of applied weight, it digitally displays the weighted value(H300-10D).

• Model number: MNP-001
• Type: Analog
• Size: 250 x 150 x 492mm
• Plate size: 80 x 60mm
• Stroke: 0 - 70mm
• Heating temperature: -20 - 200?
• Heater capacity: 160W x 1
• Temperature adjustment: Microcomputer type proportional control
• Sensor: K class thermocouple
• Power supply: 100VAC 50/60Hz
• Power cord length: 2.5m (3P plug with ground pin)
• Lead feed amount: 1 Handle rotation 4mm
• Weight: Approx 18kg
• A simple hot press convenient for testing under a low weight.
• Allows for manual adjustment of the pressure to any value.
• Only the temperature of the upper hot plate can be adjusted(MNP-001).
• Suitable for heating compression molding tests of various materials.

• Model number: MNP2-002D
• Type: Digital settings
• Size (mm): 250 x 150 x 512
• Plate size: 80 x 60mm
• Stroke: 0 - 45mm
• Weighted: Maximum approx 500kg
• Heating temperature: -20 - 200?
• Heater capacity: 160W x 2
• Temperature adjustment: PID control
• Sensor: K class thermocouple
• Power supply: 100VAC 50/60Hz
• Power cord length: 2.5m (3P plug with ground pin)
• Lead feed amount: 1 Handle rotation 4mm
• Weight: Approx 18kg
• A simple hot press convenient for testing under a low weight.
• Allows for manual adjustment of the pressure to any value.
• Only the temperature of the upper hot plate can be adjusted(MNP-001).
• Suitable for heating compression molding tests of various materials.

• Trap method: Direct trap by can body cooling method, glass condenser
• Performance: Dehumidification capacity/MAX 0.5kg (water), Minimum achieving temperature/-50?
• Safety mechanism Leakage/overcurrent breaker, frozen machine overload relay, frozen machine high-pressure switch
• Configuration: Frozen machine, refrigerant/air cooling type, output R507A 400W, Service outlet/MAX 4A (for diaphragm pump)
• Chamber dimensions/capacity: Inner diameter 90 x Depth 225mm/approximately 1.4L
• Ambient temperature range: -5 - 35?
• External dimensions: 300 x 370 x 317mm
• Weight: Approx 32kg
• Power input: 6A 600VA
• Rated power supply: 100VAC 50/60Hz (*Performance indicates the value when the room temperature is 20?, rated power voltage 50Hz, ethanol 1.3L, lid attached. *This product cannot be used as a frozen dryer. )
• Model number: UT-1AS
• Both English and Japanese are indicated to achieves convenience.
• These products efficiently collect harmful steam by utilizing temperature differences.
• Improving solvent recovery ratio in concentration devices and drying devices.
• Steam is condensed, collected and recovered more efficiently when temperature difference is larger between the boiling point of the solvent under pressure and the collection part temperature.
• HFC(hydrofluorocarbon) is eco-friendly.

• Model number: Glass condenser AS
• Both English and Japanese are indicated to achieves convenience.
• These products efficiently collect harmful steam by utilizing temperature differences.
• Improving solvent recovery ratio in concentration devices and drying devices.
• Steam is condensed, collected and recovered more efficiently when temperature difference is larger between the boiling point of the solvent under pressure and the collection part temperature.
• HFC(hydrofluorocarbon) is eco-friendly.